DIY How to turn a computer desk into a loom stand with treadles

A couple of months ago, I bought the neatest loom on Kijiji.

It’s a 2 harness Leclerc  table loom, with a weaving width of 20 inches.

It’s a joy to weave on, but my tendons were grousing about the side levers and my back was honking at me.

I figured that there had to be a cheap and cheerful way to build a stand with treadles for it….

and VOILA!!!!!  (happy dance)

I have just figured out how to do it! Wheeeeeeeee!

copyright Noreen Crone-Findlay http://www.crone-findlay.com

Several years ago, we bought a metal Ikea computer desk at the thrift store.

I didn’t like having half of the top attached at an angle.

So my beloved DH, Jim and I drilled some holes, took the angled section off and re-attached it so it was nice and flat.

I had passed the desk along to my daughter and her husband, and when they gave it back to me last week, I was inspired.

First, to make the desk a comfortable height for weaving, I cut 3 inches off the legs with a pipe cutter- whew!

That was HARD work!

I mulled over how to attach the loom to the top of the desk, as it was just a hare’s breath away from fitting properly.

I took the top apart and played with the sections to see if I could come up with a workable solution- and then- woohoo!

I discovered that the chanels for a sliding mouse pad section that were supposed to be on the under side of the desk top, fitted the crosspiece of the loom perfectly!  Jubilation!

I zip tied the sides of the loom to the desk and was happy as a clam…..

except…. for the pesky owees of the tendons grizzling about the side levels, and my back spazzing out on me.

Hmmmmm…..

Inspiration!  add lamms and treadles!

I started by cutting a support piece at the side, and bolting it to the side of the stand.

I used 2 angle brackets as the support for the lamms (with a little block to fill in excess space).

Then, I drilled holes in the lamms for cords to the levers and to the treadles.

I tied the lamms to the levers and was verrrrrrrry pleased! Things were moving along quite nicely!

There had to be a way of supporting and securing the treadles, so I used a board from an old pallet, and drilled 2 holes for the legs.  Poifeck.

I had a 6 inch length of threaded 1/4 inch steel rod, which I ran through the treadles (which I had cut out of scrap lumber).

The treadles were too wide at first, so I cut dippsy doodles into them to make them fit better.

The most frustrating part of the whole process was finding nuts that would go onto the threaded rod. Grrrrrrrrr!

I finally ended up filing the ends of the rod, as I just couldn’t get anything to thread onto the rod. Once I did that, zip! on went 2 nuts, happy as can be.

I screwed the whole treadle mechanism to the crossboard on the floor, and tied the treadles to the lamms…..

and held my breath…… what if it didn’t work? eep…..  that would have been 3 hours down the tubes….

BUT! Joy! and whee and halleujah! It works like a dream!

So, if you would like to have a floor loom, but don’t have the ca$h, watch for a table loom on the various online places, and convert a desk into a stand for it.

You’ll need to have some basic carpentry skills, and I couldn’t have managed drilling the holes through the sides of the treadles without a drill press, but I bet you could do it if you had to.

Here’s the video that I made about how to convert a computer desk into a loom stand with treadles:

Here are some notes to keep in mind if you would like to adapt my project for your table loom:

Things to look for in a desk or table that you want to use for a loom stand:
1: Being able to bolt or screw the lamm support piece along the left hand side of the table/desk legs is essential.
2: Being able to shorten the legs to drop the height of the table to a comfortable ergonomic height is also essential.
3: Being able to attach the loom to the table is one more essential. (Clamps? Zip ties? A channel like the one on mine was a piece of beautiful serendipity)

About these ads

7 Comments

Filed under eco crafts & green projects, Loom & looms & small loom weaving, weaving & handwoven

7 responses to “DIY How to turn a computer desk into a loom stand with treadles

  1. you never cease to amaze me with your creativity!

    Like

  2. You are so incredibly clever!! How do you figure stuff like this out? You amaze me too! : )

    Like

  3. Thank you so much, Elizabeth :)

    Like

  4. Aleksa

    This is amazing! There has got to be some kind of prize out there for the most creative, ergonomic problem solving ever. You go!

    Like

  5. Trisha

    Fabulous project! I have a 4 harness Dryad that I want to turn into a floor loom so I got lots of great ideas from your tutorial :) Just a tip, when you need to cut a threaded rod, thread the nut on first, then cut. When you remove the nut it will smooth out all the little rough edges and the nut will go on and off easily.

    Like

    • Thanks for the tip, Trisha :) Unfortunately, the rod had been cut before I bought it at a garage sale, so it was a big hassle, but I got there eventually :)
      I think that you will love having your Dryad converted- it is just pure delight, and it’s so delicious to have done it yourself :)

      Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s