Category Archives: video tutorial

July 21, 2012 · 12:26 pm

Setting up loom extenders on the Mirrix loom

Normally, I tend to prefer small looms, but I have just fallen in love with using loom extender bars on the Mirrix loom.

It’s really hard to convey how tall the ‘Alice in Wonderland’ version of the Big Sister 16 inch loom is when she’s got her stilts on.

With the extenders, she is 40 inches/1 m tall.

Now, that’s tall!

This means that you can achieve lots more weaving with one warp up.

(I’m working on some really fun stuff with my Big Sister Stiltie! So, stay tuned!)

My husband bought me the components for the extenders at the place he buys parts for our ancient tractor, so I didn’t have instructions on how to do this.

So, I had to figure it out for myself.

I found that there are a few tricks that make the set up easier when adding the loom extenders to your Mirrix loom.

First, lift the top of the loom off the side rails and set aside.

Unscrew the thumbscrews from the threaded rods, and screw them onto the extension rods.

I screwed them on so they were 5 inches/12.5 cm from the top end of the extensions.

Put the washers back on top of the thumbscrews.

Screw the coupler to the top of the loom rod.

Hot tip: Place the end of a tape measure inside the coupler so you can watch to see that you have screwed it on so it is half way onto the lower rod.

I had my doubts about how stable this was going to be, because the coupler seemed wobbly to me.

But, I went ahead, and screwed the extension rod in anyhow….

And, then, when I tightened it up by hand, I was amazed at how it was suddenly rock solid!

WHEEE!

This is good!

Wobbly bad!

Solid- GOOD!!!

Repeat for the other side…

Measure to be sure you have everything square, and put the top half of your loom back on.

Stand back in amazement at your loomie on stilts! Wowsa!

The best part is that the loom is still miraculously stable and works perfectly.

I find that resting it against the edge of the desk and having the lower edge sitting in my lap is the most comfortable way to weave with the extensions on.

Also, weaving standing up works well.

Having the stand for it would be sublime.

I made a video of the ‘putting it together’ process:

Happy weaving! 😀

Cheap and Cheerful alternatives for tapestry bobbins

Tapestry bobbins have a mystique around them and they can be expensive.

But, what do you do if you need a lot of tapestry bobbins and have a limited budget?

Well… you improvise.

First you analyse, then you upcycle!

After all… a tapestry bobbin is a yarn delivery device.

What does it need to do?

It needs to hold yarn in a way that allows you to pass it through a fairly small shed.

It should have a tip that will allow you to tap your weft yarn into place.

It needs to be able to hang from the tapestry while it’s parked.

So…. there are things that will work quite nicely for you as you feed your piggybank, but weave your tapestries in the meantime.

I make my own quirky, but perfect for me tapestry bobbins from upcycled wood: Link to post

Recently, I noticed that one of my fave bobbins looks a lot like a little spoon…

and of course, that started me thinking…

would a little coffee spoon work as a tapestry bobbin?

It seemed rather outrageous….

So, I took a little orphaned silver coffee spoon that had been in a box of sandbox toys that I bought for my grandson at a garage sale, and hammered the poor thing flat.

It works BEAUTIFULLY as a tapestry bobbin!

This made me think…. hmmm…. metal spoon…. hmmmm…. ~metal bobbins~…. hmmmmmm….

So, what about a 4 inch nail with a bead on the end? Would that work?

Yup. Wash it well first, and if the tip is snaggy, sand it smooth or file with a nail file.

You could paint it if you want, or coat it with a clear gel just to ensure that it won’t discolor your yarn.

Stuff a bit of tissue into the opening of the bead to secure it.

I learned about using bamboo forks as bobbins on Ravelry.

I like them!

But, I have found that they work much better if you stick a bead on the end.

Squish the tines of the fork into the bead center and you’re set to weave.

I love tatting, and used to carve tatting shuttles.

I’ve discovered that my Little Bird shuttles work beautifully as tapestry bobbins. Whodathunkit? 🙂

So, be creative and think outside the box when you are contemplating tapestry bobbins.

I mean, really… spoons and forks?

Yes!

If you are willing to experiment, you’ll find all kinds of things that will work really well in your weaving!

Here’s a video that I made about cheap and cheerful alternatives for tapestry bobbins:

Happy weaving! 🙂

2 Comments

Filed under eco crafts & green projects, Loom & looms & small loom weaving, tapestry, tutorial & how to, video tutorial, weaving & handwoven

Tagged as design

June 30, 2012 · 9:20 pm

How to weave inkle bands on the Mirrix loom part 3

Part 3 of the video tutorial series on how to weave inkle bands on Mirrix looms is about the weaving process:

Something that I learned as I trundled up my ever so steep learning curve with figuring out how to weave inkle bands on the Mirrix loom:

I started out by weaving one row on one band, putting it’s shuttle down, then picking up the second shuttle and weaving one row on the other band.

Sounds slow and clunky, doesn’t it? Well, you’re right.

The most efficient way to weave 2 bands at once is to weave as far as you can on one band, then set that shuttle aside, and weave away on the second band.

Oh… speaking of shuttles, here’s the tracing of my most favorite inkle shuttle:

I designed this one several years ago, and I love it. Works like a charm.

Here’s the video that shows the weaving process:

When you need to advance the warp, loosen the tension quite a lot.

Support the spring as you gently ooze the warp rod around and up the back of the loom.

Pat the warp strands back into the channel, and tighten up the tension again.

Remember, you do not need to have the tension as tight as when you are weaving a tapestry or beading.

You’ll find the perfect tension that suits you best.

Keep on weaving until the warp rod is sitting on top of the loom, and then check into the 4 th video in the series:

How to finish the bands.

🙂

How to weave inkle bands on the Mirrix loom part two

This is the second stage of the video tutorials that I made on how to weave inkle bands on the Mirrix loom.

There are two bands on the loom, because in this video, I am working on the 16 inch loom.

When you work on the 8 inch loom, it’s okay to just weave one band at a time, as the warping bar doesn’t flop around.

But, on the 16 inch loom, you do need to either warp up 2 bands, or secure the other end of the warping bar with a cord so it will stay perfectly horizontal.

I tried weaving 3 bands at once on the 16 inch loom, and didn’t like it, as the center knobs on the shedding device got in the way.

Two bands are just great though.

AND…. if you want to weave longer bands, and have either a 12 inch or 16 inch Mirrix loom then the loom extenders will be your friend 🙂

I use a crochet hook and a weaving stick to make the heddling process go quick like a bunny.

Here’s the video tutorial:

Start by placing a piece of cardboard between the layers at the front of the loom and the back so you can’t see the warp strands at the back of the loom.

Place the shed changing device into the brackets. Unscrew the little knob that holds the heddle rod in place.

Pull the heddle rod back so it’s about half way along the warp strands.

Place the heddles onto the fingers of your non dominant hand.

Look down at the warp strands that are at the lower edge of the front of the loom.

There’s a gap between the strands that have gone in front of the warping bar and behind it.

Slip your fingers into the gap and scoot them up to the shedding device.

Slide a shed stick into the gap.

Voila! (which is how ‘walla’ is really spelled 🙂 )

You have shed one ready to heddle!

Now, slip the crochet hook behind the first warp strand, pluck a heddle off your fingers, and pull it forward.

Catch the other end of the heddle loop and place both loops on the heddle rod.

Go slowly, and be sure that both ends of the heddle loop stay politely on the heddle rod.

When you have all of the warp strands heddled, slide the heddle bar into position in the knobs, and tighten the lock nut.

Repeat the heddling process on the second set of warp strands for your other band.

Push the first set of heddles down as you rotate the shedding device.

Leave the shed stick in place, and use the crochet hook to pick up the warp strands for the other shed.

Take the warp strand from the back to the right of the one in front, and onto the hook,

take the hook over the front strand, and pick up the next strand and carry on across.

Slide the weaving stick out of the first shed, and slip it along the crochet hook to transfer the warp strands from the crochet hook to the weaving stick.

Turn the weaving stick on it’s side, and then pick up the warp strands one at a time and capture them with the heddles just as you did for the first set of warp strands.

Repeat this process for the second band.

Check your heddles carefully to make sure that they are opening the sheds properly.

Ahhhhh! a warped loom is a thing of beauty!

Attach the handle to the shedding device and adjust the tension by turning the thumbscrews.

Open the first shed, and insert a craft stick, then open the second shed and insert another craft stick.

Squish the warp strands together to establish the width of your band.

Weave one row, leaving a 6 inch/15 cm tail.

Change sheds, and weave the next row.

Pull up firmly on the tail end and weave it through the same shed.

Repeat several times until the tail end is woven in, and the band is established.

Next video: The fun part! Wheeeeeee…. weaving…… 🙂

How to weave inkle bands on the Mirrix loom part one

I love weaving inkle (warp face) bands.

I use in dollmaking:

Link to purchase pattern for Inkle dolls: Inkle Dolls

And, they are wonderful for trimming handwoven clothing:

Link to post that shows how to shape inkle bands to make a yoke or other shaped pieces of garments: Warp pulling

Over the years, I have also made hat bands, book marks, all kinds of jewelry, key fobs, vests, bags, bag handles, the garters for the men’s kilt hose for my son’s wedding, shawls, freeform pieces that combine inkle weaving, knitting, embroidery, spool knitting and crochet, as well as rugs.

Yep. I love inkle weaving.

So, as I have been exploring the possibilities of weaving with my Mirrix looms, I had to give inkle weaving a try.

I found that it was quite challenging at first. But, I don’t give up easily 🙂

I ended up spending waaaaaaaaaaaaaaay more hours than I should have, experimenting and obsessing over making inkle bands on the Mirrix.

Well… I finally succeeded.

Since it was so challenging, I figured that I should share what I have learned, so that other intrepid inkle weavers can leap right in, without all the trial, error and frogging that I went through!

There are definitely tricks to weaving inkle bands on the Mirrix looms, and I have made 4 videos to share those tricks.

Here’s part one of the video:

Here is the draft for the bands that I wove in the videos:

To read the draft: Each square represents one warp strand.

You can check your warping by looking at each shed to see that it has the same number of strands, in the order that they appear in the line.

You will be putting a total of 8 green strands on, followed by 4 orange strands, 3 sets of (1 orange, 1 green) for a total of 6 strands, then 4 orange strands and ending with 8 green strands.

At the top and bottom of the loom, you’ll see the full count of warp strands.

At the warping bar, the 2 sheds will be separated into their correct (we hope!) configuration for each shed.

The chart will give you bands like this:

The upper band is the band on the right hand side of the loom in videos 2 – 4.

I only used the center of the draft for it, without the green border strands.

The yarn is Lion Brand Cotton.

Setting up the loom for inkle bands is different than normal warping.

You need to have the warping bar at the front of the loom.

Tie the green yarn onto the warping bar and take it up and around the loom, just the same as if the warping bar was in the back.

You will need to cut the warp strand of color 1 to tie on color 2 at the warping bar, for EVERY color change.

WHAT?!?!?!

Yes. really.

It sounds insane, but this is the biggest key to making the whole inkle thing work on the Mirrix loom.

Trust me. You ~can~ twist your yarns around each other, and are welcome to, I’m sure, if that would make you happy….

BUT…. the quickest, easiest way to have problem free warping for inkle is to cut those little darlin’s and tie the knots between the colors.

Yay! Warped! Insert the spring rod into the spring to keep the warp strands locked into their notches.

This is sooooooooooo important! (yep… voice of ‘oops’ experience here 😦 )

And in Part 2…. it’s on to the heddles.

I have a nifty, super friendly way of using a crochet hook and weaving stick to make the heddling process go like a breeze.

That’s coming up next…. so stay tuned! 🙂

3 Comments

Filed under Loom & looms & small loom weaving, tutorial & how to, Uncategorized, video tutorial, weaving & handwoven

Tagged as hand weaving, hand woven, how to weave inkle bands on the Mirrix loom, inkle, inkle weaving, Mirrix looms, narrow band weaving, Noreen Crone-Findlay, textiles, weaving inkle bands, woven bands

June 22, 2012 · 9:13 pm

How to weave Leno Lace on the Mirrix loom

I am fascinated by exploring all the different things that I can do with Mirrix looms.

While I am involved in this four month long co-creation with Mirrix looms, I am going to be looking at what I can and can’t do with the Mirrix looms.

(Guess what I am NO GOOD at? Bead weaving on the Mirrix!

Yep. All my bead weaving has been off loom and I am TERRIBLE at bead weaving on the loom.

That one came as a surprise… ah well… we shall see if that changes! )

In my previous blog post, LINK, I showed how I set up my Lani Mirrix loom, using the ‘No Warp Ends’ warping technique.

There are several advantages in setting up your Mirrix loom for the ‘No Warp Ends’ technique:

It allows you to sample different weaving techniques quickly and efficiently.

You won’t waste time OR yarn when using the ‘No Warp Ends’ technique.

I love that!

Because the ‘No Warp Ends’ warping technique precludes using a shedding device, it is perfect for weaving techniques that are hand manipulated, like: LENO lace! Yay!

I think that Leno lace is the bee’s knees.

It’s kind of a miniature version of the ancient technique of twisting fibers, called, Sprang.

You do this nifty twist thing, and tadah! You get a bonus free row that is cheerfully waiting for you, gratis! Whee!

Leno can seem a little challenging at first, so I figured that a video tutorial is a good idea.

Here it is:

Happy Weaving!

🙂

6 Comments

Filed under Loom & looms & small loom weaving, tutorial & how to, video tutorial, weaving & handwoven

Tagged as hand weaving, hand woven, how to weave Leno lace, Leno Lace, Mirrix loom, Mirrix looms, textiles, weaving techniques

June 22, 2012 · 8:10 pm

A slightly different approach to the ‘No Warp Ends’ on the Mirrix

I hate wasting yarn… so I really don’t like loom waste – who wants to toss their yarn in the trash? Really 🙂

That’s why I love Claudia Chase’s ‘No Warp Ends’ technique for the Mirrix looms.

The one thing that I wasn’t keen on was using paper clips to be the holders for the yarn ends, so I thought about it and mulled it over.

Hmmmm…. I use ‘S’ hooks all the time to hang things and connect them, but I have never used them on a loom.

This called for some experimenting.

I don’t know about you…. but, I have a tendency to start with a really complicated plan, and have to do a lot of trial and errors to get to the elegant and simple final version.

I was thinking about all kinds of ways of making harnesses to hold the bars for the ‘s’ hooks…. oh my!

I also figured that I wanted to use both sides of the loom while setting up for this technique.

I had woven two affinity bracelets at the same time- one on the front of the loom, and one on the back, so this seemed to stick in my mind as ‘the way to go’.

Well… I twiddled and fiddled, and threw away the whole overly elaborate harness idea, and ended up using 4 loops of double sided velcro to hold the bars to the upper and lower edges of the loom.

That was a big breakthrough- talk about a simple way to do this! Yay!~

And, I am really pleased with the final method that I came up with- it really works for me!

Here is the video, showing how I warp the Mirrix Lani using the ‘No Warp Ends’ technique, with ‘S’ hooks:

Happy Weaving! 🙂

8 Comments

Filed under Loom & looms & small loom weaving, tutorial & how to, video tutorial, weaving & handwoven

Tagged as claudia chase, double sided velcro, hand weaving, hand woven, Lani Mirrix Loom, Mirrix, Noreen Crone-Findlay, social networking for mirrix, warping technique, weaving, weaving techniques

June 10, 2012 · 12:28 pm

A pin a stick and a loop of string to open the shed

If you have a loom that doesn’t have a shedding device, picking up the warp strands for every row you weave can be a tedious process.

I like to use a stick, a pin and a loop of string to open the sheds. It’s a huge time saver!

I’ve made a video tutorial on how to do this for narrow bands, but this technique also works on wider pieces, too.

Pick up every other warp strand with a weaving stick (even a popsicle/craft stick or a paint stick will work).

Push that stick up to the top of the loom.

Now, use a knitting needle to pick up the ~remaining~ warp strands, to open the second shed.

You’ll be going over the strands that you went under in the first shed, and under the ‘overs’.

Take a loop of string (in this case, I used 2 string heddles from one of my inkle looms held together for more strength, and to make it easier to see in the video) through the open shed.

Pick up the end of the loop with a kilt pin, and then lift the loop strings between each warp strand onto the pin.

Take the second end of the loop up onto the pin, and close it.

Adjust the length of each section of the loop.

And, Voila! you now have a handy, dandy way of opening both sheds!

Here’s a pic of the shuttles that I make by upcycling old rulers and bits of decorative trim:

HOT TIP that I mentioned in the video: If you use a file folder as the separator/background thingie between the front and back of your loom, you can use the pocket of the file folder to park your shuttle and beading needle when you’re not weaving.

And, here’s the video tutorial:

1 Comment

Filed under Loom & looms & small loom weaving, tutorial & how to, video tutorial, weaving & handwoven

Tagged as heddles, hints and tips for weaving, how to make shuttles, how to open sheds on a mirrix or frame loom, Mirrix loom, Noreen Crone-Findlay, shed sticks, social networking for a mirrix loom campaign, upcycled rulers, weaving sticks

May 31, 2012 · 10:38 pm

Making string heddles for my Mirrix loom

At the beginning of May, a ‘new-to-me’ loom , a large Mirrix tapestry loom, arrived in my studio. (Courtesy of my son and daughter in law who picked her up in the city 4 hours away, that used to be her home- the previous owner didn’t want to ship her).

I immediately sat down and made a whole lot of heddles for her, as she didn’t come with them.

And then, I warped her up- ooooooooohhhhhhhhhh, I love how easily she warps! Bliss!

As I was warping her up and starting to weave, I thought…. ‘Hmmmm…. there must be a group for Mirrix weavers on Ravelry’

(Ravelry= the facebook of the yarn world)

I looked, and sure enough! There is a Mirrix group…. which I joined, pronto.

And the first thing I saw was that Claudia (the inventor of the magical Mirrix looms) and Elena, her talented daughter, had posted that they were accepting applications for their annual ‘Social Networking for a Mirrix Loom’ campaign. Link

Well… I had decided within hours of starting to weave on my ‘Joni’ loom that I wanted to fill my studio with Mirrix looms.

So, I sent off an application….

Um… I wanted to fill the studio with ~Smaller~ Mirrix looms!

MEANWHILE>>>> The Joni is one big Mamma, and even though I am tall, my arms are short, so I found that I was having shoulder pain.

My clever daughter in law subtly sneaked the information out of me that I was longing for the treadle kit for the Mirrix loom. Then, she orchestrated the family buying me the treadle kit for Mother’s Day! What a sweetheart!

To say that I was thrilled was an understatement!

THEN! on the 18th of May, was just tickled pink to hear from Elena that they had picked me as one of their team for the 4 months of the ‘Social Networking’ campaign. Whee! What a couple of thrilling days!

And, now… I am starting to keep my part of the bargain, which is to chronicle my experiences with the Mirrix loom(s).

So, since I began my Mirrix adventures with making string heddles, I am going to show you my quick and easy way of making the string heddles for the Mirrix looms (or inkle or frame looms, too).